Regular Maintenance of Slate Floors

Natural stone products such as Slate need to be sealed for it to look its best, the sealer brings out the best in the natural features and also protects the stone from dirt becoming ingrained in its pores and once that happens it becomes difficult to clean effectively and starts to lose its appearance.

A good example of this is the Slate Tiled Floor shown below where that we were asked to maintain in Edinburgh, the sealer had worn off allowing the stone to dull and the grout to become stained.

Slate Tiled Floor Before Cleaning Edinburgh

Cleaning Slates Flooring and Grout

There was still evidence of the previous sealer on the floor so the first job was to strip that off completely using a 50:50 solution of two Tile Doctor products, Pro-Clean and Remove and Go. The two products combined together make a powerful cleaner/stripper combination which was left to dwell and soak into the tile and grout for 10-15minutes.

Next step was to scrub the solution into the floor using a scrubbing pad fitted to a rotary machine and a stiff narrow brush was run along the grout lines. The now dirty solution was then extracted from the floor using a wet vacuum and the process repeated until all the previous sealers and coatings had been removed from the floor. The floor was then given a clean using just Pro-Clean to make sure all dirt had been removed again using a wet vacuum to extract the solution.

The final part of this process was then to give the floor a rinse with a diluted solution of Tile Doctor Neutral Cleaner to remove any trace of strong cleaning products and the wet vacuum was used to get the floor as dry as possible ready for sealing the next day.

Slate Tiled Floor Stripped Ready for sealing Edinburgh

Sealing Slate Floor Tiles

The floor was left overnight to dry and the following day we returned to seal the floor checking first it was dry. Sealing was done by applying five coats of Tile Doctor Seal and Go which will protect the floor going forward, adds a nice low sheen and works very well on Slate, Quarry and Victorian tiles.

Slate Tiled Floor After Sealing Edinburgh

The Slate floor came out really well and the tiles and grout now look like they were recently installed.
 
 
Source: Slate Floor Maintenance Service in Edinburgh

Restoring a Slate Tiled Kitchen Floor

These photographs below are of a Slate Tiled Kitchen floor taken at a customer’s house in Henley-on-Thames which, as its name suggests, sits alongside the River Thames in Oxfordshire. My client’s Slate kitchen floor had recently been cleaned with unsuitable cleaning products which I suspect impacted the sealer leaving it looking dull. Sealers really to improve the look of a stone floor so unsurprisingly once the sealer had been damaged my client had been unable to find a cleaning product that could have any kind of positive effect on the tiles.

Slate Tiled Floor Before Cleaning Henley-on-Thames

It’s fairly well known that many supermarket quality cleaners are only really designed for use on Ceramic or Porcelain tiled floors as they contain acids which strip away at sealers and acid sensitive stone floors, leaving the stone beneath vulnerable. So your select a cleaning product for your floor always read the small print on the back of the label and make sure you avoid anything that mentions not for use on acid sensitive stone; belter still Tile Doctor have a number of products for cleaning tiled floors including Neutral Cleaner and Stone Soap.

Cleaning a Slate tiled floor

To clean the floor and remove any remaining sealer I first made a strong dilution of Tile Doctor Pro Clean which is a strong alkaline cleaner and then spread this over the floor, leaving it to dwell. This allows the cleaner to seep into the slate and get underneath, breakdown sealers and start to lift out ingrained dirt.

Following a dwelling period of roughly ten minutes, I agitated the floor periodically with a rotary machine fitted with a black scrubbing pad and scrubbed along the grout lines with a stiff grout brush. I then used a wet vacuum to extract the resultant slurry away and then followed up by rinsing the floor with clean water, and once again vacuumed up the residue.

Any stubborn areas were retreated until I was happy with the floor and then I left the floor to dry off completely overnight, in preparation for sealing the following day.

Sealing a Slate tiled floor

Upon my return to the house the following day, I ran some damp tests on different parts of the floor to check for any excess moisture which could potentially damage the performance of the sealer. Once I was satisfied that the floor was completely dry, I proceeded to seal the tiles using Tile Doctor Seal & Go. This will provide a robust surface seal for the future, along with an aesthetically pleasing low-sheen finish.

This sealer works particularly well on Slate tiles and, being a water-based sealant, additionally Seal & Go does not emit an unpleasant smell as it dries. Slate is quite a porous stone so I applied six coats of seal to provide long-lasting protection.

Slate Tiled Floor After Cleaning Henley-on-Thames

 
 
Source: Slate Tiled Floor Cleaning and Restoration service in Henley-on-Thames

Removing Years of Dirt from Slate Kitchen Tiles

I recently visited a client living in the market town of Woodstock in Oxfordshire to rejuvenate a fantastic multi-coloured Slate floor that had been hidden under several years’ worth of dirt in their kitchen. Slate is a typically hard-wearing tile used for flooring high traffic areas of houses and public buildings but does need sealing to bring out its best features and in this case the sealer had long since worn off and dirt had become ingrained in the stone.

Multi Coloured Slate Before Cleaning Woodstock

Cleaning a dirty Slate tiled floor

My first task in the cleaning process was to mix a strong solution of Tile Doctor Pro-Clean, which is a strong alkaline cleaner safe to use on Tile and Stone, and NanoTech HBU (Heavy Build-up Remover), which is a particularly powerful product that uses nano-sized particles to tackle muck in areas of the stone where typical cleaners simply can’t reach. I spread this solution across the floor and left it to seep into the stone, to get underneath and lift out the ingrained dirt.

After allowing the solution adequate time to dwell, I scrubbed the floor with a carbon brush to gradually reveal the fantastic natural colours of the Slate hidden beneath. Following this, I rinsed the entire floor several times with clean water, before soaking up the resulting soiled residue with a wet vacuum.

Multi Coloured Slate During Cleaning Woodstock

The next part of the cleaning process entailed paying particular attention to the grout lines. I used Tile Doctor Grout Clean-Up to scrub the grout lines and also to treat a small amount of efflorescence. The resulting residue was promptly extracted with the wet vacuum and I finished by giving the whole floor a rinse with Tile Doctor pH Neutral Tile Cleaner. This is a day to day tile cleaning product which is recommended for stone floors, many supermarket tile cleaning products are only suitable for ceramic tiles due to their acidic formula and can damage a floor over years of use so you should always read the label. I then left the floor to dry completely overnight.

Multi Coloured Slate During Cleaning Woodstock

Sealing a Slate tiled floor

On day two, the Slate tiled floor was dry and ready to seal. The floor had to be completely dry, as any excess moisture has the potential to the damage the performance of the sealer. Since my client had specifically requested a matte finish, I opted to use Tile Doctor Colour Grow. Colour Grow is an impregnating sealer that provides durable surface protection from within while also enhancing all of the natural mineral shades.

Multi Coloured Slate After Cleaning Woodstock

My client was very pleased with the results, particularly as they hadn’t realised they had such a great looking floor in their house when they had first purchased it!
 
 
Source: Slate Floor Cleaning and Restoration service in Oxfordshire

Slate Kitchen Floor Rejuvenated

This floor was installed in the house of a client in the town of Trowbridge, Wiltshire, I was asked if I could restore the Slate tiled kitchen floor back to its former glory. The client was having trouble cleaning the floor themselves due to the sealer being worn away and dirt now becoming ingrained into the pores of the slate. I suspect the life of the sealer had been reduced by the use of in-appropriate cleaning products; anything even mildly acidic will overtime eat away at the sealer and reduce its life.

Upon arriving at the house, I undertook some test cleaning to demonstrate to the client the results I would be able to achieve. Seeing how quickly I would be able to make a marked difference to the appearance of the tiles, the client quickly commissioned me to undertake a clean and seal for the entire floor.

Slate Floor Before Cleaning and Sealing in Trowbridge

Cleaning a Slate tiled floor

My first task was to mix a solution of Tile Doctor Pro-Clean and clean water. This was then applied evenly onto the floor and left to dwell for 15 minutes, allowing for the strong alkaline cleaner to soak into the stone to get underneath any ingrained dirt, and lift it to the surface.

Once the solution had rested on the surface for a short while, I paid particular attention to the grout lines, scrubbing them with a stiff grout brush. Next, I attached a polybrush to a rotary machine and scrubbed all of the tiles thoroughly. I then used a wet-vac machine to soak up any resulting residue.

However, upon further inspection, I noticed some further paint splashes and grout haze. I applied Tile Doctor Grout Clean-Up to tackle the evident grout haze, and used a heavy duty scraper to remove the paint splashes. Once my client and I were happy with the result, I vacuumed up the slurry and gave the entire floor a thorough rinse. It was then left to dry completely overnight.

Sealing a Slate tiled floor

I returned the next day to seal the floor. Firstly, I tested the floor for evidence of damp using a damp meter and, once I was happy that there was no excess moisture to potentially damage the performance of the sealer, I proceeded to seal the floor using Tile Doctor Seal & Go, which provides a durable surface seal and leaves an aesthetically pleasing sheen finish.

Slate Floor After Cleaning and Sealing in Trowbridge

I applied a total of six coatings of the sealer, resulting in a marked difference in the appearance of the tiles (as you can see from the photos). She was very happy with her refreshed floor, and I left her with some cleaning and maintenance advice for the future, before making my departure.
 
 
Source: Slate Tile and Grout cleaning and polishing service in Wiltshire

Deep Cleaning Dirty Slate Tiles

This slate floor was installed in the kitchen of a house in the town of Burton-on-Trent in Staffordshire. As the name suggests, Burton-on-Trent sits alongside the River Trent, which runs through most of the northern Midlands. The old sealer on my client’s Slate tiled kitchen floor had completely worn off and, as a result, dirt had become ingrained in the pores of the stone which was now in need of restoration.

Slate is typically a very durable tile, having been used both residentially and commercially for hundreds of years but, in particularly high traffic areas like kitchens it’s important to maintain the sealer or dirt will get into the pores of the stone making the floor difficult to clean effectively and leading to the tile looking worse for wear. I was commissioned to get the floor back to good health and I prescribed a deep clean and re-seal.

Slate Tiled Floor Before Cleaning Burton-on-Trent Slate Tiled Floor Before Cleaning Burton-on-Trent

Cleaning a dirty Slate tiled floor

To start the cleaning process, I first diluted Tile Doctor Pro-Clean and water and left it to soak into the floor for a while so it could get to work lifting out the dirt from the pores of the stone. Pro-Clean is a versatile, high alkaline cleaner safe to use on natural stone which can be diluted in different strengths depending on the level of soil build-up. In this case, I opted for a reasonably strong solution due to the significant amount of ingrained dirt (as shown by the photographs).

After about ten minutes I started working in small sections to agitate the tiles with a scrubbing pad attached to a rotary machine. The pad and machine take a lot of the hard work out of the cleaning process although I usually do the grout by hand using a stiff scrubbing brush. Once I had finished the initial clean, I rinsed the entire floor with water, before repeating the process multiple times until I was satisfied that I had got the Slate tiles as clean as possible.

Sealing a Slate Tiled Floor

After completing the clean, I left the house for a few days to allow the floor enough time to dry before being sealed. As any Tile Doctor will tell you, all moisture must be removed from a tiled floor before sealing it, as it has the potential to compromise the effectiveness of the sealer.

Once I was satisfied that the floor was completely dry, I sealed the tiles using four coats of Tile Doctor Seal & Go, which provides a stain resistant surface seal and a nice, low sheen finish. Seal & Go is a water based product (so no smell) and is suitable for use on a wide variety of unsealed, porous surfaces as Slate, Victorian tile, Sandstone, and textured Quarry tiles.

Slate Tiled Floor After Cleaning Burton-on-Trent Slate Tiled Floor After Cleaning Burton-on-Trent

As you can see, the overall results were fantastic and my client was really happy with the difference I’d been able to achieve.
 
 
Source: Professional Tile, Stone and Grout cleaning and maintenance services in Staffordshire

Restoring the Appearance of a Slate Tiled Floor

Every now and again, I get called to work on tiled floors which have were laid some time ago and not properly maintained in a long time, as was the case with this customer in the town of Bedford at the heart of Bedfordshire. They had a twenty year old Slate tiled floor that was now in need of a thorough clean and a re-seal.

Cleaning a Slate tiled floor

As you can see from the photos, the floor was very much worse for wear in some areas, with the tiles looking very dull and dirty. To clean the tiles I used a combination of a steamer and a solution of Tile Doctor Pro-Clean, a high alkaline cleaner suitable for use on many different types of natural stone floor, including Slate, Limestone, and Victorian tile – just to name a few.

The solution is scrubbed into the tiles to lift out the ingrained dirt and stains. Concentrated Pro-Clean is also strong enough to strip off the old sealer from the floor. After completing the clean and inspecting the tiles to ensure all of the problem areas had been successfully tended to, I rinsed the floor thoroughly with water to remove any trace of cleaning product. After rinsing the floor in such a way it is important to leave plenty of time for it to dry before sealing, so I left the house for 24 hours before returning.

Slate Tiled Floor Bedford after Cleaning and before sealing

Sealing a Slate tiled floor

Upon my return to the house, I inspected the floor to ensure it had dried completely, as any excess moisture remaining of the tiles has the potential to damage the performance of the sealer. The sealer I used was the new and improved Tile Doctor Seal & Go known as Seal and Go Extra, which has an acrylic base and a much higher content of solid. This means that when the sealer dries it is able to provide an even better level of protection for the stone.

I applied several coats of Seal & Go Extra to give the Slate tiles a stain resistant surface seal and the high quality finish the client had requested. Seal & Go Extra is suitable for use on internal and external, unsealed porous surfaces such as textured Quarry, Sandstone, Victorian tile and, of course, Slate.

Slate Tiled Floor Bedford After Cleaning and sealing

 
 
Source: Professional Tile, Stone and Grout cleaning services in Bedfordshire

Sealing Black Slate Tiles

I recently visited a client’s house in the small town of Okehampton, an area with a lot of heritage. It was first settled by the Saxons, and like many other towns in the South West, grew as a result of the thriving medieval wool trade.

The client asked me to take a look at the black Slate tiled floor in her kitchen, which she noticed had gone quite dull in a short period of time. She mentioned that the sealer she had been sold and subsequently applied two years ago had completely gone, even though she believed it was supposed to last ten years. This is a common misconception in the tiling world; it seems that the tiling company my client had previously consulted did not sell her the appropriate cleaner, nor did they mention that sealer should, in fact, be topped up at least once a year.

Black Slate before cleaning and sealing in Okehampton

Cleaning a black Slate tiled floor

I cleaned the floor using Tile Doctor Remove & Go, which can be used not only on Slate, but also on other types unpolished natural stone. This product is a multi-purpose stripper which will remove the old sealer from the floor whilst also lifting out any ingrained dirt and stains.

After applying a layer of Remove & Go, I left it to dwell for 20 minutes. I then used a black buffing pad, which is suitable for heavy duty wet scrubbing, to work the product deep into the tiles. After cleaning, the old sealer had been completely removed and the floor was ready for a new seal. I rinsed the floor several times with clean water to remove any trace of cleaning product, before leaving it to dry overnight ready for sealing the next day.

Sealing a black Slate tiled floor

Tile Doctor Seal & Go was my choice of sealer for this floor, as it is designed for use on internal unsealed porous surfaces like Slate, as well as textured Quarry, Sandstone and Victorian tile. I applied four coats of Seal & Go for a stain resistant surface seal along with a high quality, low sheen finish.

Black Slate after cleaning and sealing in Okehampton

After cleaning and sealing, the floor was no longer looking dull – instead the fantastic shade of black was really emphasised. Both myself and my client were very pleased with the results. I hope to be back at some point within the next year to top up the seal (as is recommended) and maintain the condition of the floor in this high-traffic area of the house.
 
 
Source: Professional Tile, Stone and Grout Cleaning service in Devon

Revamping Dirty Slate Tiles

The photographs below are from a property in the small village of Mayfield, located within the High Weald civil parish of Mayfield and Five Ashes in East Sussex. The village is perhaps best known for its annual carnival and torchlight procession however on this occasion I was there to revamp the Slate tiled kitchen floor. The tiles had been left worse for wear by the previous occupants where years of children and mucky dogs had taken its toll on the slate.

Slate floor before cleaning in Mayfield Slate floor before cleaning in Mayfield

Cleaning a Slate tiled floor

Whilst I would normally utilise my buffing machine with a black buffing pad as part of the cleaning process for natural stone tiles, I was unable to do so in this case as the Slate tiles in the kitchen were riven which would of cut into and potentially shredded the pad.

As a result, I had to clean the floor by hand. I did this using a solution of one part Tile Doctor Pro-Clean to five parts clean water, which I worked into the tiles with a deck brush, followed by a hard brush. The solution needed will vary in accordance to the level of soil build-up on the floor. In this case, the soil build-up was light enough to use quite a diluted solution, but in a case where a floor is very heavily soiled I would recommend using a more concentrated solution of one part Pro-Clean to two parts water.

After a period of scrubbing with the hard brush, I sucked up the muck that had been removed from the surface with a wet-vac machine. I then continued with the cleaning process for several hours, before once again using the wet-vac machine up any excess moisture left by the cleaning solution. I left for a period of two days to allow the floor to dry completely before I returned to seal the floor. I instructed my client to keep the floor completely dry because any excess moisture would potentially impact negatively on the performance of the sealer.

Sealing a Slate tiled floor

To seal the floor I used Tile Doctor Colour Grow, a colour intensifying sealer which gets into the pores of the stone protecting it from within. In this case I applied two coats of Colour Grow to really bring out the range of fantastic natural colours and shades in the Slate, whilst also providing durable surface protection for this high-traffic kitchen area.

Slate floor after cleaning in Mayfield Slate floor after cleaning in Mayfield

My client was very impressed with the results. I hope she enjoys this brilliant feature of her new home, now full of life and colour once again.
 
 
Source: Professional Tile, Stone and Grout Cleaning service in East Sussex

Cleaning Very Dirty Riven Slate Kitchen Tiles

I was recently contacted by a client who had just moved into a house in Crowborough, a town in East Sussex which by the way was once home to Sir Arthur Conan Doyle, the author of the Sherlock Holmes novels and short stories. The riven Slate tiled floor in the kitchen had trapped bits of dirt and also food which had become ingrained in the tile. Needless to say, the new homeowner wanted to give the kitchen floor a thorough clean. However, she had tried every cleaning product she could find in the supermarket, but to no avail. Struggling to find a solution she sought out professional assistance and naturally I was happy to help.

Slate floor before cleaning Crowborough

Cleaning a Slate tiled floor

My first task was to mix up a strong solution of Tile Doctor Pro-Clean. The product was only slightly diluted with water, since the floor was quite heavily soiled and a higher concentration of Pro-Clean was needed to help remove several layers of dirt and food waste. Once applied to the floor, the solution was left to dwell for roughly five minutes before I began to work it into the stone with a deck brush. I did the best I could here to clean the floor without using my buffing machine as, since the floor was riven, my black buffing pad would have been ruined by the ridges.

Making up for the lack of a buffing machine, I made sure to scrub the floor with Pro-Clean for several hours to remove as much grime as possible. One the cleaning was finally completed I rinsed the floor several times with clean, hot water. I then used a wet-dry vac machine to remove any excess moisture to clear the floor for sealing when I returned 48 hours later. Upon leaving, I left my client with instructions to avoid spilling anything on the floor as, again, any liquid left on the surface might affect the performance of the sealer.

Slate floor during cleaning Crowborough

Sealing a Slate tiled floor

After a period of two days, I returned to commence the sealing. My choice of sealer was Tile Doctor Seal & Go, which is suitable for use on internal, unsealed surfaces such as Slate, textured Quarry, Victorian tile, and others. Seal and Go is also a water based sealer so you there’s very little smell given off whilst it dries compares to solvent based sealers. In this case, the client did not want the surface of the floor to be too shiny, so I only used two coatings of Seal & Go, whereas for a shinier result I would have used a few more.

Slate floor after cleaning Crowborough

My client was exceptionally pleased with the results, which had not only cleaned the floor but brought out the beautiful colours in the stone that had once been hidden under several layers of muck.

Slate floor after cleaning Crowborough

 
 
Source: Professional Tile, Stone and Grout Cleaning service in Crowborough

Restoring the Look of a Chinese Slate Tiles

I recently made a trip down to South Molton, a small town which sits on the River Mole. The river, actually a tributary of the River Taw, gets its name from the two small towns it runs by, North Molton and South Molton. Anyway I digress, my client asked me to take a look at a Chinese Slate floor in her house, as it was in dire need of a good clean due to the original sealer having worn off over time allowing the dirt to become ingrained in the tile.

Chinese Slate Before Cleaning in South Molton

As this particular type of floor is naturally quite rough, I advised my client to have the Slate milled flat. This would not only make the floor easier to clean on a regular basis, but also it would reduce the hazard of people tripping over the exposed edges. However, the milling procedure is expensive due to the need to use a special grinding disc formed of diamond segments, which is then attached to a rotary machine and used on the stone. My client decided against this, instead opting for a thorough clean and seal. This would be the first time the floor had ever received a proper clean – it had not even been cleaned when the tilers first fitted it!

Cleaning a Chinese Slate floor

My choice of product for the cleaning was Tile Doctor Pro-Clean, a high alkaline cleaner which, along with Slate, is suitable for use on other natural stone floors such as Limestone, Granite and Travertine. The product, diluted with clean water, was applied evenly to the floor using a Polybrush, as well as a rotary machine fitted with a buffing pad. This also helped to remove any remaining old sealer although, as aforementioned, the vast majority of the old sealer had already worn away.

Following this, I cleaned the grout using Tile Doctor Grout Clean-Up and a long-handled stiff grout brush. Grout Clean-Up penetrates below the surface of the grout to lift out grout haze and general dirt. After completing the cleaning I rinsed the floor several times with clean water to remove any trace of cleaning product. The floor was then left to dry completely before sealing, as any moisture left over on the floor could have impacted on the sealer.

Sealing a Chinese Slate floor

When I returned to seal the floor I opted to use Tile Doctor High Shine Sealer, which is suitable for use on textured natural stone floors, as well as textured ceramic, textured porcelain, and a range of others. Five coats of High Shine Sealer were applied, providing the floor with durable surface protection and a nice high-sheen finish. This dramatically improved the appearance of the floor to the point that it is hard to believe this is the first time it has been treated to a proper clean and seal!

Chinese Slate After Cleaning in South Molton

Both myself and my client were very pleased with the results. Chinese Slate is one of the most beautiful and characterful types of stone for tiled floors, so it was very rewarding to be able to make such a difference here.
 
 
Source: Professional Tile, Stone and Grout Cleaning service in Devon

Maitaining a Slate Fireplace Hearth

I thought you might find this post interesting as it’s a little unusual. I had arrived at a client’s house in Boars Hill near Oxford to do a travertine floor and she asked if I could also take a look at her fireplace where one of her dogs had urinated on it. Urine is acidic so if not quickly removed it will start to eat away a sealer and in this case as you can see from the photo below it left a mark. It was quite a small area and as I already had the necessary products to deal with it I said no problem.

stained slate fireplace hearth Boars Hill Before

Cleaning a Slate Fireplace Hearth

The urine had penetrated the existing protective seal so to get a uniform appearance it was going to be necessary to remove the covering and re-seal. To do this I covered the hearth in Tile Doctor Remove and Go which is a tile and stone friendly product for removing of protective coatings. This was carefully scrubbed into the stone and bit by bit the old wax/seal was removed exposing the bare slate.

Sealing a Slate Fireplace Hearth

The stripped slate was now clean and all trace of previous sealer had been removed but once it had fully dried was left looking washed out. This was easily remedied however by applying a coat of Tile Doctor Stone Oil which brought back the deep black colour. When the Stone Oil had dried I finished the job off by applying a coat of Tile Doctor Ultra Seal which is a natural look sealer that will protect the slate going forward.

stained slate fireplace hearth Boars Hill After

 
 
Source: Professional Tile, Stone and Grout maintenance service in Oxfordshire

Removing Old Coatings From Slate Tiles

These slate tiles had been laid in the kitchen of a farmhouse in the village of Little Hampden around twenty years ago and since that time had become heavily soiled with a build-up of dirt and over applied sealants.

Slate Tiled Kitchen Farmhouse Floor Before Cleaning in Little Hampden

Cleaning a Slate Tiled Floor

To get the floor clean a strong dilution of Tile Doctor Pro-Clean was applied to the floor, allowed to soak in for a while and then scrubbed into the tile and grout with the aid of a commercial rotary machine. Once done the floor was washed down with water which was then removed along with the soiled cleaning solution using a wet vacuum.

The Pro-Clean removed the top soiling throughout the floor but it became clear that something stronger would be need to remove the heavy build-up of old sealants. Fortunately we have a product called Tile Doctor Remove and Go which is designed to strip floors of sealers so this was applied to the floor in a similar fashion as before and this tackled the problem. The next task was to clean the grout lines with Tile Doctor Grout Clean-up and give the whole floor a final rinse with more water to ensure any chemical residue is removed leaving the floor ready for sealing.

Sealing a Slate Floor

The floor was left to dry overnight and I came back the next day to seal it to protect for years to come and improve the general look of the slate which really does look better when sealed.

To seal the floor I used a combination of products to get the best results. First a coat of Tile Doctor Colour Grow was applied which is a colour enhancing impregnating sealant which occupies the pores in the stone protecting it from within and then a number of coats of Tile Doctor Seal and Go were added to add a nice subtle sheen to the floor.

Slate Tiled Kitchen Farmhouse Floor After Sealing in Little Hampden

Our customer was extremely pleased with the results and took up our offer of a Tile Doctor maintenance contract to enable her to keep the floor in pristine condition.
 
 
Source: Professional Tile, Stone and Grout maintenance service in South Buckinghamshire

Refreshing a Slate Tiled Kitchen Floor

Pictures below of a slate tiled kitchen floor that I recently maintained at a house in Burton on Trent. The problem was the usual one that the sealer had worn down and the floor had lost its polished look leaving it dull and the owner of the house wanted it looking new again.

Cleaning black slate floor tiles

The floor was cleaned using a dilution of Tile Doctor Pro-Clean which was left to soak into the slate for ten minutes before being worked into the tile using a rotary machine fitted with a scrubbing pad. The process was repeated where there were stubborn stains and then the whole floor was washed down to remove the soiled cleaning solution and any trace of product. The floor was then dried as much as possible using a wet vacuum and left to fully dry overnight.

Slate Tiles in Burton on Trent Before Cleaning Slate Tiles in Burton on Trent Before Cleaning

Sealing Slate floor tiles

I left the floor overnight to dry then came back next day and used a damp test meter to verify the floor was dry and ready for sealing. Once happy I proceed to apply four coats of Tile Doctor Seal & Go which as you can see from the photograph below has really brought the slate back to life.

Slate Tiles in Burton on Trent After Cleaning Slate Tiles in Burton on Trent After Cleaning

The customer was delighted with the transformation of the floor.
 
 
Source: Professional Tile, Stone and Grout maintenance service in Staffordshire

Refreshing A Very Dirty Slate Tiled Floor

This Multi-Coloured Slate tiled floor in the kitchen of a property in Barnard Gate near Witney was in good solid condition with no damage but had been poorly maintained with layers of sealer applied to un-clean tiled; the new home owners were keen to make this floor into a talking point as you entered the property and asked us to address the problem.

Coloured Slate Tiled Floor Barnard Gate Before Cleaning

Deep Cleaning a Slate Tiled Floor

The first task was to remove the layers of sealer from the tile so on day one the floor was covered with Tile Doctor Remove and Go which was left this to dwell for a while so it could soak into the pores of the slate and penetrate the remaining sealer. The product was then scrubbed into the tile with a Rocky rotary floor scrubber and then rinsed off with clean water and dried with a wet vacuum. The next process was to clean the floor with a strong mix of Tile Doctor Pro Clean to remove the remaining dirt in the floor and to scrub the grout clean, again the rotary floor machine came in useful for this task and again the floor was thoroughly rinsed with clean water a few times and dried with the wet vacuum. I then left the floor for a couple of days to allow enough for it to completely dry before sealing.

Sealing Slate Kitchen Tiles

To seal the slate I first applied a coat of Tile Doctor Colour Grow which is an impregnating sealer the gets into the pores of the stone and also enhances the natural colours. I then applied a few coats of Tile Doctor Seal and Go which is a topical sealer that added a nice sheen finish that the customer wanted.

Coloured Slate Tiled Floor Barnard Gate After Cleaning

The end result was fantastic and the combination of the two sealers really got the best from the slate which is now very much appreciated and loved by the customer.
 
 
Source: Tile, Stone and Grout Maintenance and Restoration in Oxfordshire

Deep Cleaning Old Slate Tiles

A customer in Telford recently bought this barn conversion in the village of Ince, Cheshire. The building had Riven Slate floor tiles installed on the ground floor from hallway and corridor through to the utility room and downstairs WC. The tiles were not looking their best and in fact the old polyurethane based sealer had gone yellow and started to peel off in places. The building was originally built in 1886 and is grade 2 listed and after an initial attempt to bring the floor back to life didn’t work out as planned the owner decided to get in touch.

Riven Slate Tiled Floor Ince Before Cleaning Riven Slate Tiled Floor Ince Before Cleaning

Cleaning a Quarry Tiled Floor

To get the floor back to its original state so it could be re-sealed the old sealer would have to be completely removed from the tiles, fortunately we have a product available that does exactly that called Tile Doctor Remove and Go. Working in sections the tiles were covered with a dilution of Remove and Go which was left to soak into the slate for twenty minutes before being scrubbed in used a rotary machine fitted with a stiff brush head. The resultant soiled solution was then removed from the floor using a wet vacuum and the process repeated until all the old sealer had been removed and the floor was looking clean again. Additionally it was necessary to steam clean the whole floor and scrub stubborn areas with a hand brush. After the whole floor was clean I gave it a thorough wash down with fresh water to remove any trace of cleaning product and then used the wet vacuum to get as much water off the floor as possible and reduce drying time.

Riven Slate Tiled Floor Ince During Cleaning

Sealing a Quarry Floor Sealing

I left the floor to dry off for a couple of days and then returned to apply the sealer checking the moisture level of the floor first to ensure it was dry enough to take a sealer. I had discussed the various options for sealing and the customer wanted a satin finish so it was decided to use Tile Doctor Seal and Go which is a water based sealer that provides the require finish and being water based can be applied without leaving a solvent smell as it dries, four coats of Seal and Go were needed to fully seal the slate.

Riven Slate Tiled Floor Ince After Cleaning Riven Slate Tiled Floor Ince After Cleaning

It was quite a large area and originally I had estimated it would take two days to remove the old sealer and get the tiles clean in the end however it took three days due to clean the floor due to the state of the tiles and a day to seal. The customer and his wife were really happy with the result and left the following feedback for me on the Tile Doctor feedback system.

I would like to commend Jozsef on his hard work and tile doctor on their faith and training in there staff to achieve such a high standard in an end result. The experience from start to finish has been a very pleasant one. Jozsef was very professional, polite and punctual, knowledgeable, very hardworking and trustworthy. Both my wife and I would not hesitate to recommend Tile Doctor & Jozsef.
Many Thanks again Mr & Mrs Pasquali
 
 
Source: a Tile, Stone and Grout Renovation in Shropshire

Restoring the Appearance of Brazillian Slate Tiles

This beautiful Brazilian Slate tiled floor was installed in the kitchen of a house in Barrow-in-Furness, Cumbria; the slate has been previously sealed with a number of products including Varnish and the overall effect was inconsistent making the floor dull and had done little to bring out the true beauty of the natural stone. Additionally varnish is quite brittle and easily scratched by furniture etc. so never a good choice for sealing a floor.

The situation needed to be remedied so during my visit I did a small test to strip off the old sealants, clean the tile and re-seal; the effect was transformational so they booked me to come back in a few weeks’ time to finish the job.

Varnished Brazilian Slate Tiles Before Cleaning

Removing Varnish from slate floor tiles

To transform the floor and guarantee the final appearance its necessary to remove all the previous products applied to the floor stripping it back to its natural state and then seal again. So I got started stripping off the varnish and other sealants from the floor slate using a dilution of Tile Doctor Remove and Go which is a tile friendly product designed to remove coatings from natural stone. The solution is sprayed onto the floor, left to soak in and then agitated using a floor buffer fitted with a black scrubbing pad. The soiled solution is then rinsed away and removed using a wet vacuum.

This process removed most but not all of the varnish and sealers so the next step was to apply NanoTech UltraClean which is a gel that you apply and leave for 30 minutes before adding water and agitating with a scrubbing pad. This did the trick and now not only was the slate clean of all coatings the grout had come up nice and clean as well. The whole floor was given a thorough rinse to remove any trace of product and then dried as much as possible using the wet vacuum to soak up the water.

Varnished Brazilian Slate Tiles Before Cleaning

Sealing Brazilian Slate Tiles

The floor was left to dry off overnight and I returned the next day to seal the tiles checking first with a damp meter to ensure they were no longer damp. All was well so I proceeded to apply the sealer with a paint pad applicator. For this we had agreed on Tile Doctor Seal and Go which is ideal for slate as it really does transform the look of slate and adds a nice satin finish, the Slate was quite porous so five coats were needed in total.

Varnished Brazilian Slate Tiles Partly Sealed Varnished Brazilian Slate Tiles Sealing

I think you will agree the Brazilian slate tiles look much improved; certainly the customer was happy with the results. Before leaving I gave them some advice about aftercare and what products to use when cleaning the floor in future for best results.

Varnished Brazilian Slate Tiles Finished

 
 
Source: Tile, Stone and Grout Problems resolved in Cumbria

Putting the life back into Slate Floors

Details below of a tired Slate and Flag Stone floor installed in a house in Cookham, Berkshire; the client was actually the son of an existing client whose floor we had also cleaned recently. The existing sealer had been wearing away over time and the floor had becoming increasingly ingrained with dirt making it difficult to keep clean, the solution was to strip the floor back and re-seal it.

Flagstone Floor Cookham Before Cleaning Slate Floor Cookham Before Cleaning

Stone Floor Cleaning

To clean and strip the tiles of the remaining sealer the floor was soaked in a solution of Tile Doctor Pro-Clean and scrubbed in using a weighted rotary machine to help loosen the soils and break down the sealers. The soiled solution was removed and it was clear some areas of the floor needed further attention to remove the sealer so an application of Tile Doctor Remove and Go was applied which was left to soak in for a while to assist in breaking down the sealer before being scrubbed again. Once the floor was clean and the sealer was gone the floor was rinsed using our hot truck mounted extraction system and was then allowed to dry for 36 hours.

Stone Floor Sealing

When we returned I checked to make sure the floor was dry and ready to seal, all was well so I then sealed both the Slate and Flagstone floors with six coats of Tile Doctor Seal and Go using a paint pad applicator.

Slate Floor Cookham After Cleaning Flagstone Floor Cookham After Cleaning

The floor looked much improved when finished I took time to explain how to clean the floor using a Neutral Cleaner that will extend the life of the sealer, the customer was pleased with the service and left the following comment on the Tile Doctor feedback system.

“We are very pleased with the results.
Peter Young, Cookham

Source: Tile, Stone and Grout Maintenance in Berkshire

Deep Cleaning Slate Tiles in Glasgow

Slate is a hard-wearing product ideal for floors however it does need a sealer to bring out the best in it and sealers do wear off after a few years and this had happened with the Slate tiled floor in this post. The floor was now looking dull and the grout had also discoloured so time to call in Tile Doctor to breathe new life into the tile and grout.

Dark slate tiled floor glasgow before cleaning

Cleaning a Slate Floor

It’s not a good idea to apply a new sealer on-top of existing as it can affect the final result so the first task was to strip back the floor to the natural stone giving the Slate and Grout a thorough clean in the process.

To do this a strong solution of Tile Doctor Tile Doctor Pro-Clean was applied and left to soak into the floor for about 20 minutes; Pro-Clean has a strong alkaline base so it’s safe to use on Stone as opposed to a weak acid cleaner. After twenty minutes it was worked into the slate and grout using a low speed bonnet machine fitted with a black scrubbing pad with the excess extracted using a wet vacuum.

This process was repeated three times to make sure all the old sealer and dirt was completely removed and after this the grout was cleaned by hand using more Pro-Clean and a stiff brush. Once done the whole floor was then neutralised with more water to ensure there was no trace of cleaning product remaining on the floor prior to sealing.

Grout Colouring

The floor was left to dry off overnight and returned the second day to colour the grout to dark grey which made a big improvement to the overall look of the floor; the grout colours we use come in 12 colours so we can usually find one that matches the customers’ requirements, once applied they also form a great barrier preventing future staining. Once the colourant has dried the floor was given a further clean with Tile Doctor Neutral Cleaner which is an everyday cleaning product we recommend for sealed floors.

Sealing a Slate Floor Sealing

The floor was left to dry and we came back two days later to re-seal the tile for which we used five coats of Tile Doctor Seal and Go which is a great sealer for Slate tiled floors as it leaves a low sheen finish whilst providing excellent stain protection. I should mention that Seal and Go is also a water based sealer so it doesn’t leave a smell whilst it’s drying.

Dark slate tiled floor glasgow after cleaning

We left the floor to dry overnight again and came back the third day to seal the Slate tiles for which we used six coats of Tile Doctor Seal and Go which give a subtle shine to the tiles and matched the customers requirements.
 
 
Source: Tile, Stone and Grout Restoration Service in Glasgow

Maintaining Slate Floor Tiles

This customer from Chelwood Gate which is a small village south of East Grinstead contacted me asking for the Slate tiles in their kitchen, utility room and living area to be cleaned and sealed. It was quite a large area, approximately 70sq meters.

Slate Tiled Floor Chelwood Gate Before Cleaning Slate Tiled Floor Chelwood Gate Before Cleaning

Deep Cleaning a large Slate Tiled Floor

Once we had cleared the large sofas and fridge freezer from the room I got to work cleaning and stripping the floor using a strong dilution of Tile Doctor Pro-Clean. I was slightly concerned by the large ridges on the tiles but made a start with the buffer fitted with a black scrubbing pad. Straight away the pad was shredded on the ridges so it became clear the floor would have to be completed manually using a deck brush and elbow grease. Once the floor was clean and stripped of any remaining sealer I gave it a thorough wash down to remove any cleaning product and extracted as much water as possible with a wet vacuum Luckily the room was well ventilated with several exits and large doors which aided the drying process.

Slate Tiled Floor Chelwood Gate During Cleaning

Sealing Black Slate Floor Tiles

After two days I returned to a dried out floor which was ready for sealing. We have a number of different sealers available; each one has a different effect. After discussing this with the customer they requested a shiny surface with improved colouring, so for the next five hours I applied four coats of Tile Doctor Seal and Go which is a water based sealer that gives a nice shine which matched their needs.

Slate Tiled Floor Chelwood Gate After Sealing Slate Tiled Floor Chelwood Gate After Sealing

You can see from the pictures the difference and amazing before and after result. We were unable to move one of the freezers in the utility room so I left the customer with a small bottle of Seal and Go to apply himself once the floor had dried enough to move the unit without scratching the sealer.
 
 
Source: Tile, Stone and Grout Cleaning Service in Sussex

Restoring Slate Tiles In A Listed Building

This is a 25m2 Slate tiled floor installed in a grade 2 listed coach house in the village of Hemingford Grey on the banks of the river Ouse. It was originally called the six bells and the original coach house sign is still hanging from its original ironwork in the entrance lobby. The slate floor was laid through the kitchen and hallway in 2000 and since then it had just been mopped and extra coats of polishes/waxes had been applied leading to a build-up.

Slates Tiles Hemingford Grey Before Cleaning

Cleaning the Slate Tiled Floor

Before starting work I protected the kitchen units and Aga cooker in plastic film to protect against splashing and mopped onto the tiles a dilution of Tile Doctor Remove and Go which is a coatings remover. Remove and Go I should mention is not only an effective cleaning product but as its name suggests is ideal for removing sealers from floors.

To get the floor completely clean you need to strip it back to bare tile and because of the layers of sealer we let the Remove and Go soak into the Slate tile for some time before being worked in using a rotary machine fitted with a black scrubbing pad. Then rather than wash the product away we blanketed the floor in a polythene sheet and left for two hours.

Slates Tiles Hemingford Grey During Cleaning

The polythene sheet prevents the floor from drying out and allows the chemical process of breaking down the layers of sealant to take place. After removing the sheet we scrubbed the floor again before removing the residue with our high powered internal pressure washing tool.

Slates Tiles Hemingford Grey After Cleaning

The floor was now bare and all the natural colours in the slate became far more evident. The tiles do need to be bone dry before sealing however so we left it to dry out for a day and left a number of special air blowers setup around the floor to assist with the drying.

Slates Tiles Hemingford Grey After Cleaning

Sealing the Slate Tiled Floor

When we returned the third day the floor was dry so we sealed it using five coats of Tile Doctor Seal and Go which is a water based sealer (so no smell) that add good stain protection as well as adding a nice subtle sheen to the tile which really enhanced the colours in the slate.

Slates Tiles Hemingford Grey After Sealing Slates Tiles Hemingford Grey After Sealing

The customer was ecstatic with the result, so much so that before we left she gave us a thank you card in an envelope. On returning to our unit we opened the card and out dropped £50, well I was amazed, even though we explain all the processes to our clients and take the upmost care at their homes we really didn`t expect that level of generosity. This is how the card read:

“To Mick,
Thank you to you and Tom for your high quality in Service, Integrity and Value x Excellent craftsmanship. Much appreciated. So pleased with your work.
Kind regards. M. Evans

It was a pleasure to work for such a nice lady and we look forward to returning in the New Year to restore some more stone and terracotta flooring for her.
 
 
Source: Tile, Stone and Grout Cleaning Service in Cambridge

Restoring Slate Floor Tiles

This Slate Tiled floor belongs to a client who had recently bought an old Oast House in Hastings. They were in the process of restoring it and when lifting up the floor discovered an original slate floor underneath it. As the photos show it was in a very poor state and they were unsure whether to rip it up or see if it could be renovated.

Slate Tiled Floor Hastings Before Cleaning Slate Tiled Floor Hastings Before Cleaning

On arrival they showed me the floor and told me of their dilemma; we provide a free no obligation home survey so after a thorough inspection I proceeded to run a test clean on a small section to see how well it would come up. This involved applying a 3-1 dilution of Tile Doctor Pro-Clean and working it in with a stiff brush and hand held buffer with a black scrubbing pad. I was very pleased to see the floor come up really clean and informed them I was very confident that not only could I get the floor clean it would amazing when finished. The clients were happy to hear the good news and gave me instructions to go ahead

Cleaning black slate floor tiles

On my return I applied the same strong 3:1 dilution of Tile Doctor Pro-Clean to the floor that I used before letting it soak into the tile for ten minutes before using a stiff brush and large buffing machine fitted with a scrubbing pad to clean the entire floor Slate tiled floor. When finished I went over the floor again looking for stubborn areas and spot treating them until I was happy with the result. Once happy I gave the floor a good rinse using fresh water to remove any trace of cleaning product from the floor and using a wet vacuum to remove the fluids and get the tiles as dry as possible.

Sealing Slate floor tiles

I left the floor for two days to allow time for it to completely dry out and returned to seal it using Tile Doctor Seal and Go. I applied four coats of sealer which gave the floor a fantastic finish and though the clients were initially weary of the shine I explained that it would dull down over a short period as it cured. Before leaving I gave them advice on how to keep the tiles clean and recommended the use of Tile Doctor Neutral Tile Cleaner which is a neutral PH cleaner that will not reduce the integrity and longevity of the sealer; they were both very happy with the end result as was I as the difference after was striking.

Slate Tiled Floor Hastings After Sealing Slate Tiled Floor Hastings After Sealing

Source: Tile, Stone and Grout Cleaning Service in Sussex

Dealing with Very Dirty Slate kitchen tiles

This Shell Slate tiled floor was installed in the kitchen of a house in Lytchett Minster and had not been sealed after its installation over twenty years ago and had now become deeply ingrained with dirt which the owner could not remove however hard she tried.

Cleaning Shell Slate Tiles

To clean the tiles I used Tile Doctor Pro-Clean diluted one part cleaner to five parts water, the solution was applied it to the floor and then left to soak in for ten minutes before working it in with a Numatic buffing machine fitted with 17″ medium firm brush. Next the tiles were steamed using an Earlex steamer and stubborn stains cleaned by hand using sections from a cut-up black buffing pad and a Spid brass-coated wire brush where necessary. Being riven slate the floor was too uneven to successfully clean using a black buffing pad fitted to a rotary machine as the sunken parts of the tile would have been missed and so cleaning tile by tile was the only option to ensure the slate was returned to the best possible condition. A stiff brush was also run along the grout lines before thoroughly rinsing the floor to remove any trace of cleaning product.

Shell Slate at Lytchett Minster Before Cleaning

Sealing Shell Slate Tiles

The floor was left to dry overnight and I returned the next day to seal using two coats of Tile Doctor Colour Grow sealer which is a penetrating sealer that occupies the pores in the tile preventing contaminates from lodging there and enhances the many beautiful colours of the Slate as well as leaving a subtle shine to floor.

Shell Slate at Lytchett Minster After Cleaning

The customer was very pleased with the result and said that she hadn’t before seen the true colour of her floor.
 
 
Source: Residential and Commercial Tile and Stone Cleaning in Dorset

Maintaining Slate Kitchen Tiles

Another example of a tired Slate Tiled floor that was in need of a clean and seal, this time in the industrial town of Corby famous for its iron and steel works.

Slate floor before cleaning Corby Slate floor before cleaning Corby

Cleaning Slate Kitchen Tiles

To get the Slate tile and grout clean the a dilution of Tile Doctor Pro-Clean was applied which was left to soak into the tile for ten minutes before scrubbing it in with a rotary machine fitted with a black scrubbing pad and then using a stiff grout brush to clean along the grout lines.

Slate floor during cleaning Corby Slate floor during cleaning Corby

The floor was then thoroughly rinsed using clean water which was then removed using a wet vacuum; there were a few stubborn areas that needed further attention which were re-treated. The last step of the cleaning process was to use a high pressure cleaning tool that extracts as well as washes, we normally use this tool for cleaning carpets but it also does a great job of giving a hard floor a thorough rinse to remove any trace of cleaning product before sealing.

Slate floor during cleaning Corby Slate floor during cleaning Corby

Sealing the Slate Tiled Floor

The floor was left to dry and we came back the next day to seal the slate using five coats of Tile Doctor Seal and Go applied using a paint pad applicator. I usually use Seal and Go for slate tiles as it provides good stain protection with adds a nice sheen finish that adds to the look of the floor.

Slate floor during sealing Corby
The job took two days and the floor now looks transformed.

Slate floor after sealing Corby Slate floor after sealing Corby

Source: Residential and Commercial Tile and Stone Cleaning in Northamptonshire

Maintaining A Slate Staircase

These photographs were taken some time ago however I thought they might be interesting as Glasgow has an interesting mix of architecture and occasionally we are asked to clean some unusual buildings including this one which had a stone winding staircase faced with slate tile which was overdue for a clean and seal.

Slate tiled stairs in Glasgow before Slate tiled stairs in Glasgow before

Cleaning a Slate Tiled Staircase

Stairs are a high traffic area and if there was any sealer left on the slate treads it was minimal so I decided to apply a strong dilution of Tile Doctor Pro-Clean. This was left on to soak into the slate tiles for about 20 minutes before being scrubbed in by hand (no room for a rotary machine).

Slate tiled stairs in Glasgow before

This was worked into the slate and grout until I was happy the tile and grout was clean. The soiled cleaning solution was removed using a wet vacuum and the floor neutralised with more water to ensure no chemicals remained on the floor prior to sealing.

Sealing a Slate Tiled Staircase

It was a small area so it only took a few hours for the tiles to dry so later that afternoon I was able to seal the slate for which we used five coats of Tile Doctor Seal and Go which adds a nice subtle sheen finish and will protect the tiles from staining going forward.

Slate tiled stairs in Glasgow after Slate tiled stairs in Glasgow after

 
 
Source: Residential and Commercial Tile and Stone Cleaning in Glasgow

Cleaning and Sealing Slate tiles in a Kitchen

These photographs of a Slate tiled floor were taken in the Kitchen of a house in Towcester where the slate was looking rather dull and had lost its appeal. This does happen with natural stone floor where the sealer which can add a shine to the stone becomes worn down and ineffective.

Towcester Slate Tiles Before Cleaning Slate Tiles Towcester Before Cleaning

Cleaning Chinese Slate Tiles

We removed the kickboards from the kitchen units and lined the skirting boards with green Frog tape in order to protect them from cleaning fluids. The next step was to soak the floor in a dilution of Tile Doctor Pro-Clean which we let soak into the tile for 10-15 minutes before scrubbing it in with a rotary machine fitted with a black pad and then using a stiff grout brush to clean out the grout lines.

Slate Tiles Towcester Scrubbing Slate Tiles Towcester Scrubbing

The floor was then thoroughly rinsed using clean water which was then removed using a wet vacuum. The floor was now free of sealers etc. and this showed up a few stubborn areas that needed to be retreated and washed down again. It’s important to give the floor a good rinse to ensure it’s free of any cleaning products as they can upset the sealer.

Slate Tiles Towcester After Cleaning Towcester Slate Tiles After Cleaning

Sealing the Slate Tiled Floor

The floor was left to dry and we came back the next day to seal the slate using five coats of Tile Doctor Seal and Go applied using a paint pad applicator. I usually use Seal and Go for slate tiles as it provides good stain protection with adds a nice sheen finish that adds to the look of the floor.

Slate Tiles Towcester After Sealing Slate Tiles Towcester After Sealing

The job took two days and the floor now looks much better and much easier to clean, certainly the customer was very pleased and left the following message on our feedback system.

Phil is extremely professional and provided excellent customer service. He explained the process in detail and did a thorough job and worked extremely hard. The job was completed in the time proposed with a brilliant result. We have no hesitation in recommending Phil to others. Thank you.
Pete and Angie, Towcester
 
 
Source: Residential and Commercial Tile Cleaning Services in Northamptonshire

Deep Cleaning Slate tiles in Cumbria

This property in Ulveston had previously been used as a guest house and was now being refurbished and turned back into a home. The kitchen and conservatory had a Slate tiled floor and as you can imagine had seen a fair amount of wear from the numerous fried breakfasts that had been prepared in there. The owners had decided to replace the kitchen but were keen to keep the slate floor however it was in a bad state and looked as if it had never been cleaned and sealed for some time.

I did a small test using Tile Doctor Remove and Go (which you can see in the photograph below) and it came up really well, naturally we were booked to come back and finish the rest of the floor which I had estimated would take two days.

Slate Floor in Ulveston Test Area Slate Floor in Ulveston Test Area

Cleaning Slate Floor Tiles

Two weeks later I turned up at 9am as agreed and set up my equipment, the kitchen had already been removed so with the exception on the cooker little preparation was required. I worked in small areas using a high pressure spinner tool to remove as much dirt off the tiles as possible and a wet vacuum to remove the soiled water.

Slate Floor in Ulveston Before Cleaning Slate Floor in Ulveston Before Cleaning

Stubborn areas were treated with Remove and Go and then I moved onto the next job which was to clean up the grout. For this I used a strong dilution of Tile Doctor Pro-Clean which is a alkaline tile and grout cleaner that is safe to use on natural stone. It was scrubbed in using a stiff brush and then rinsed off with clean water, again using the wet vacuum to remove the soiled solution. The floor was now clean but still damp so I tidied up my tools and left for the day.

Slate Floor in Ulveston After Cleaning Slate Floor in Ulveston After Cleaning

Sealing Slate Floor Tiles

The Next day I came back and inspected the floor to ensure it was dry and that I hadn’t missed anything. All was well so I started to seal the floor with five thin coats of Tile Doctor Seal and Go which is an ideal sealer for slate as it adds a nice subtle sheen to the tile and being water based there is no smell as it dries. The sealer was applied using a paint pad applicator and each coat took around about twenty minutes to dry.

Slate Floor in Ulveston After Sealing Slate Floor in Ulveston After Sealing

When it was complete and the floor had dried I packed up my equipment and spent some time talking to the customer to check they were happy with the results (they were very happy) and to advise them on how to maintain the floor using with a neutral tile cleaner going forward which will help extend the life of the sealer.
 
 
Source: Residential and Commercial Stone Floor Cleaning in Cumbria

Removing Grout Haze from Slate Kitchen Tiles

These Slate tiles were installed in the kitchen of a house in Glasgow and as you can see from the photograph below they were looking dull and tired and there was evidence of grout haze over a lot of the tiles. The Tile Doctor diagnosis was that a face lift was in order for which a deep clean and re-seal was prescribed.

Slate Tiles in Glasgow Kitchen Before Cleaning

Cleaning a Slate Floor

The first step was to sweep up all the loose debris from the floor; we scrub the floor quite hard during our work so it’s important to remove any grit that could scratch the surface of the tile. We then mixed a dilution of Tile Doctor Remove and Go 50/50 with Nanotech Ultra Clean and began to work the solution into the floor allowing it to dwell for around an hour first (This process helps to soften and break down the remains of the sealer on the stone). We used a hard deck scrubber to agitate the chemicals and loosen the dirt and old sealer from the floor which is then extracted from the surface using a wet vacuum and rinsed down with clean water several times to make sure all chemicals are removed.

The next step was to apply a dilution of Tile Doctor Grout Clean-up which was then scrubbed the floor once again with hard deck scrubber. This broke down and removed all of the cement/ grout haze that the installer had left over the surface of the tile, again the floor was then rinsed with water and extracted to remove any chemical residue.

The floor was scrubbed again this time using a dilution of Tile Doctor Pro-Clean to make sure all old sealer, cement, grout haze and dirt had been completely removed. We then give the floor a thorough and final rinse and mopped the tiles with Neutral Tile Cleaner to neutralise any remaining trace of chemicals and removed the solution using the wet vacuum before leaving the floor to dry overnight.

Sealing a Slate Floor Sealing

Once the floor was dry it was then sealed using five coats of Tile Doctor Seal and Go which was chosen to provide the desired finish that the customer wanted.

Slate Tiles in Glasgow Kitchen After Cleaning and sealing

 
 
Source: Help cleaning Slate tiled floors

Maintaining Slate Tiles in Glasgow

The photographs below are from the Kitchen of a house in Glasgow with a Slate tiled floor fitted. The sealer on the slate has started to go and if you look closely at the photographs you can see how tired and dull the tiles are looking; this is a common problem with natural stone floors where you will find the sealer wears down and dirt starts to penetrate into the tile making it difficult to clean effectively.

Slate Kitchen Floor Tiles Glasgow before cleaning Slate Kitchen Floor Tiles Glasgow before cleaning

Cleaning a Slate Floor

The first job with any clean and seal work of this nature is to protect the kitchen units by removing the kick boards and then to remove any sealers and coating from the tile so when you re-seal you’re not trapping in dirt or layering on top of another potentially incompatible sealer.

The original sealer had almost worn off so a strong dilution of Tile Doctor Pro-Clean mixed 50/50 with NanoTech Ultra Clean was applied and left to soak into the floor for about 20 minutes. Pro-Clean is a multi-purpose cleaning product that will strip a sealer off the floor if weakly diluted whereas the NanoTech Ultra Clean adds tiny abrasive particles into the mixture increasing the cleaning power of the solution. This was worked into the slate and grout using a buffing machine fitted with a black scrubbing pad until I was satisfied the floor had been stripped and cleaned of all surface coatings and dirt. All the dirty water was extracted with a wet vacuum and the floor neutralised with more water to ensure no chemicals remained on the floor prior to sealing.

Sealing a Slate Floor Sealing

The floor was left to dry and we came back two days later to re-seal the tile for which we used five coats of Tile Doctor Seal and Go which is a great sealer for Slate tiled floors as it leaves a low sheen finish whilst providing excellent stain protection. I should mention that Seal and Go is also a water based sealer so it doesn’t leave a smell whilst it’s drying.

Slate Kitchen Floor Tiles Glasgow after cleaning Slate Kitchen Floor Tiles Glasgow after cleaning

Overall I was quite pleased with the floor although there were some stubborn grout stains that proved to be tough to shift.

Source: Stone and Tiled floor cleaning services in Glasgow

Restoring Slate Tiles in Historic Stratford

This beautiful Brazilian Slate tiled floor was installed in the cellar of a house in Urmston, Manchester; the slate has never been sealed as so as you would expect it dirt soon became ingrained into the pores of the tile and it lost its appearance.

Brasilian Slate Floor in Urmston before cleaning

Cleaning slate Floor Tiles

I gave the floor a good deep cleaning using a dilution of Tile Doctor Pro-clean which is an alkaline cleaner safe to use on natural stone such as Slate; I should mention this is an industrial strength product and it’s very good at removing general dirt, grime and even grease. I let the product soak into the tile for five minutes before scrubbing it into the slate using a black scrubbing pad fitted to a rotary machine. Pro-Clean was also used along the grout lines to get them clean, although this had to be scrubbed by hand with a stiff brush. Finally I gave the floor a through rinse using hot water to make sure that no chemical remained on the tile before sealing and then left for the evening so the floor could dry.

Sealing Slate Floor Tiles

The next day I checked the floor was dry and then began to seal it using five coats of Tile Doctor Seal and Go which provides stain protection and leaves a nice shiny finish.

Brasilian Slate Floor in Urmston after cleaning

I think you will agree the Brazilian slate tiles look much improved.
 
 
Source: Stone and Tile floor restoration services in Greater-Manchester

Cleaning and Sealing Slate Tiled Floors

These slate tiles were installed in the back kitchen of a house in the seaside resort town of Bognor Regis, they were in good physical condition but unfortunately any sealer had worn off some time ago causing them to lose their appearance and look faded.

Slate Tile Cleaining Floor Bognor Regis Before

Cleaning Slate Tiled Floors

Dirt had become ingrained into the tile so I went straight for a powerful cleaning combination of Tile Doctor Pro-Clean Tile and Grout cleaner mixed 50:50 with NanoTech UltraClean. The UltraClean adds tiny abrasive particles to the Pro-Clean making it a more effective cleaning product. The solution was left to dwell on the floor for a while before being scrubbed into the tiles with a rotary machine fitted with a black scrubbing pad; as usual a stiff hand brush was used along the grout lines to get them clean.

Slate Tile Cleaining Floor Bognor Regis During

The soiled solution was removed using a wet vacuum and floor thoroughly rinsed down with clean water. Pro-Clean works as a stripper as well as a cleaner and so any remaining sealer was also removed in the process.

Sealing Slate Floor Tiles

This process took a day so the floor was left to dry overnight and we came back the next day to seal it with five coats of Tile Doctor Seal and Go which is the ideal sealer for Slate tiles as it provides good stain protection with leaves a nice sheen finish; Seal and Go is also water based so there’s no smell like you get with other sealers.

Slate Tile Cleaining Floor Bognor Regis Finish

The slate tiles now look 100% improved and the sealer should keep them that way for two to three years depending on floor traffic.
 
 
Source: Professional Slate Tile Cleaning Service in Hampshire